Crown XTi 1002 Power Amplifier (500W x 2)

Two-Channel, 500W @ 4Ω Power Amplifier

Crown does it again! Their power amps are near-legendary, and the XTi 2 series is yet another example of rock-solid, powerful, innovative power amplification. Here, the XTi 1002 is packed with Peak Plus Limiters that give you full control over threshold, attack, and release. What's more, the Enhanced Subharmonic Synth section gives you control over frequency, gain, and filter type, so you can tune your XTi 1002 to your system. Beyond that, there are three fan modes you can choose from - normal, early, and fullspeed - so you can match the fan performance to your needs. Other noteworthy features include system monitoring for software visibility of AC line voltage and power supply temperature, integrated cast-aluminum handles for easy handling and dependable durability, a locking power cord clip, high-tech control software, and 29 user-definable presets. Bottom line? The XTi 2 series, including the XTi 1002, gives you an excellent solution for power amplification. Choose the one that best meets your power needs.

Features:

• Stereo Wattage: 700W @ 2 ohms, 500W @ 4 ohms, 275W @ 8 ohms
• Bridged Mono Wattage: 1000W @ 8 ohms, 1400W @ 4 ohms
• Peak Plus Limiters provide the ultimate in system performance and protection by allowing full control over threshold, attack, and release
• Enhanced Subharmonic Synth section provides user control over frequency, gain and filter type for system-specific tuning
• 3 User-defined fan mode controls - normal, early and fullspeed - for matching fan performance to a specific application
• New system monitoring provides software visibility of AC line voltage and power supply temperature
• Integrated cast-aluminum handles for easy handling and enhanced durability
• Locking power cord clip provides a secure connection between the amplifier and power cord
• Updated HiQnet Band Manager and System Architect control software
• Increased number of presets to a total of 30; 29 of which are user definable

Specifications:

• Output Power:
  700W @ 2 Ohms Stereo (per Channel)
  500W @ 4 Ohms Stereo (per Channel)
  275W @ 8 Ohms Stereo (per Channel)
  1400W @ 4 Ohms Bridged-Mono
  1000W @ 8 Ohms Bridged-Mono
• Damping Factor: 20Hz to 1kHz > 500
• Input Sensitivity: 1.4Vrms
• Input Impedance:
  20k Ohms (Balanced)
  10 kOhms (Unbalanced)
• Gain: 32.9dB @ 1kHz, 8 Ohm Rated Output
• Frequency Response: (at 1 watt, 20Hz - 20kHz) +0dB, -1dB
• Signal-to-Noise Ratio:
  XTi1002/2002/4002: 100dB (A weighted)
  XTi6002: 103dB (A weighted)
• Total Harmonic Distortion (THD): < 0.5%
• Connections:
  Input Connectors: XLR, one per channel
  Link/Out Connector: Loop-thru signal from input connector for linking another amplifier, one per channel.
  Output Connectors: Two Neutrik Speakon NL4MP output connectors. Channel-1 Speakon is wired with Ch. 1 and Ch. 2 outputs for use with optional single 4-conductor cable. Two binding post outputs (in parallel with Speakon connectors).
  HiQnet USB Connector: Type B, connects to HiQnet network.
• Controls Front Panel:
  Level: Two front-panel rotary level controls, one for each channel
  Power Switch: On/Off switch applies AC power to the amplifier
  Sel/Prev/Next Buttons: Three buttons near the LCD screen that are used to access menu items and front panel lockout
  LCD Screen: Backlit liquid crystal display that shows preset and processing status
• Indicators:
  Signal Indicator: Green LED, one per channel, illuminates when a very low-level signal is present at input (may be used for troubleshooting cable runs).
  -10 Indicator: Green LED flashes when output signal exceeds -10 dB below clip.-20 Indicator: Green LED flashes when output signal level exceeds -20 dB below clip
  Ready Indicator: Green LED, one per channel, illuminates when the amplifier is ready to produce audio.
  Clip Indicator: Red LED, one per channel, turns on at the threshold of audible distortion
  Temp Indicator: Red LED, one per channel, illuminates under excessive temperature conditions
  Power Indicator: Blue LED illuminates when the amplifier has been turned on and has power
• Cooling: Proportional speed fan with front-to-rear airflow.
• Power Consumption: 6.8A; no more than 38W at idle
• Power Requirements: 100 VAC, 120 VAC, 220-240 VAC 50/60 Hz
• Dimensions: 19 x 3.5 x 12.25" (48.26 x 8.89 x 31.11cm)
• Weight: 18.5 lbs (8.4kg)
• Specialties:
  DSP Includes EQ, Crossover Filters, Delay, and Subharmonic Synthesizer
  Protection for Short Circuits, Overloads, and Overheating