Rane MP 2016S
Rotary Knob DJ Club Mixer with 6 Stereo Inputs, Split Cueing, 4 Dedicated Stereo Phone/Line Preamps
|Overview||The MP 2016S is a rotary-controlled mixer featuring six Input Channels, Booth and House Outputs, Pre-Effects Tape Outputs, Post-Effects Tape Outputs with Level control, switchable Effects Loop, and Headphone Cueing. Input Channels 1 through 4 feature high quality RIAA phono preamplifiers which may be switched to line input via rear panel switches. Input Channels 5 and 6 each provide a balanced mic preamp with Input Gain trim, Mic/Line switch, two-band EQ, Mic Engage switch and an internal Booth Ducking enable jumper. In addition to the six dedicated preamplifiers, all six Input channels may select any of the five stereo Auxiliary Inputs.
Each Input Channel provides a 6-position source selector, Input Gain control for matching levels, Signal/Overload indicators and a studio-grade Master Mix control.
The Booth Output may select Master or Cue as its source. An ultra-low noise, high power headphone amplifier also allows monitoring the Master Mix or Cue Mix.
The MP 2016S improves on the original MP 2016 by adding Split Cue. Individual Cue switches on each channel drive a panning Master / Cue control for the Headphone output.
The Master Mix circuit provides Signal/Overload indicators, Mono switch and high-pass/rumble filters. In addition, the Master Output features patent-pending high performance 3-band, full-cut, Accelerated-Slope tone controls.
The MP 2016S provides exceptional ergonomics, good feel and a clean, intuitive layout packaged in a compact 19 inch, 3U rack mount chassis, a scant five inches deep.
So you say,"Great, but to accommodate the diverse needs of all DJ mixing styles, I need dedicated high performance three-band, full-cut, Accelerated-Slope tone controls for each of the six Input Channels, high-performance Active-Crossfader with full range contour control, A-Post-B crossfader assign switches and a stereo, 10-segment, peak dBu Master/Cue meter with peak hold; all without effecting the ergonomics of my classic rotary mixer."
We've got you covered! With the flip of a switch on the MP 2016S front panel, you can engage the optional XP 2016S External Processor and acquire all of these features.
The XP 2016S is an optional external processor designed specifically for use with the MP 2016S. The XP 2016S is intended to mount above or below the MP 2016S. It connects with a single 10-inch ribbon cable and is engaged with the flip of a switch on the MP 2016S front panel. If an XP 2016S is not connected, the XP 2016S engage switch on the MP 2016S has no effect.
The XP 2016S provides dedicated Accelerated-Slope, 3-band, full-cut tone controls for each of the six stereo Input channels, A-Post-B Crossfader Assign switches for all six Input channels, a high-performance Active Crossfader with full range Contour control, and a stereo 10-segment peak dBu Master/Cue Meter with peak hold.
The six stereo, post Mix Level signals in the MP 2016S are fed to the XP 2016S. When the XP 2016S is not engaged, the post Mix Level signals go directly to the Master Mix in the MP 2016S. When the XP 2016S is engaged, the stereo Master Mix comes from the XP 2016S.
If all Input channels on the XP 2016S are assigned Post-Crossfader, the Mix will be identical to the MP 2016S (with the addition of tone controls for each Input channel). For Crossfader control, simply assign a channel to the A or B side of the Crossfader. The Active Crossfader features a full-range Contour control for smooth blending or ultra fast cuts.
The Master/Cue Meter follows the source selection of the headphone monitor on the MP 2016S. If Master is selected, the
XP 2016S Meter monitors the pre-house-level Master signal. If Cue is selected, the XP 2016S meter monitors the Cue Source.
The XP 2016S matches the MP 2016S ergonomics, packaged in a compact 19 inch, 3U rack mount chassis, 5 inches deep.
|Comments||comments powered by Disqus|